Solar Garden Light Colloidal Silver Maker -Simple and Very Low Cost a
Solar Garden Light Colloidal Silver Maker- very low cost
Hello all.
I am not here to debate the merits or otherwise of colloidal silver.You can do your own research.You have a computer in front of you and search engines galore.
So instead of visiting porn/facebook/twitter,etc,etc all day ,a few minutes research won't harm you.
I am not here to spoon feed.I find helping people a thankless task and they are mostly obnoxious,ignorant ingrates.
i have come to advise you all about this innovative method of making it,that is all..feel free to spread this around...
i tested the output of solar garden lights and they give out an output voltage from 7 v to 13 volts depending on model and this is usually pulsed rapidly.
( i used a diode capacitor smoothing filter to measure the voltage.
(optional:- you can either smooth it using a diode/capacitor or just leave it as is.)
simply remove the led and attach your 2 silver wires which should be spaced by 1 inch to 2 inches apart to the leads to which the led was attached.
insert parallel silver wires into a glass beaker filled with boiled water.That is it.Very simple.
colloidal silver will be produced very slowly and of very high quality by a solar garden light at night automatically as solar garden lights switch off during the day to charge the battery.Off course you can start it manually by covering up the light sensor or solar cell to simulate darkness.
the whole thing can be build out of the garden solar light including attaching the silver wires to THE HOUSING!
only costs $2 for solar garden light plus silver rods which cost $20 i think...
it can be left next to the window...MAKE SURE WATER FILLED BEAKER IS SHIELDED FROM THE SUN to avoid degrading colloidal silver.use silver paper or cardboard,etc.
the pulsed very low current of less then 0.0003 amps and 7 to 13 voltage spikes will produce very small particles of silver.
some solar lights produce about 7 or 8 volts and some 13 volts.
but in any case this IS very cheap and very simple and very effective way of doing it.
also instead of removing the led altogether just cut ONE of the led's leads and use the output from their to connect to the silver wire rods.
in effect the led will be in series with one of the rods and will give a visual indication of current flowing through the water.The led could be even angled downwards towards the water into which the electrodes are immersed and be even bright enough to show you the colloidal silver as it turns cloudy very slowly.
optional:- replace WHITE LED with RED LED as RED LED absorbs only 1.5 volt instead of 4 volts.
It will take a long time to make the colloidal silver but this is not for MTV attention span people.Set it and forget it on the window sill.
optional refinement:- A piezo sounder with a inert plastic rod glued to it and dipped in the water connected to both silver rods in parallel and immersed in the water can act as a ultrasonic sonic stirrer.. .but it will take even longer to make the colloidal silver which will be of very high quality.
Remember lower currents produce higher quality and smaller sized colloidal silver particles.
any comments?
velly velly cheep. no i am not chinese either,that was a joke.You will be grateful to know.
lol
Solar Garden Light Colloidal Silver Maker- very low cost
Hello all.
I am not here to debate the merits or otherwise of colloidal silver.You can do your own research.You have a computer in front of you and search engines galore.
So instead of visiting porn/facebook/twitter,etc,etc all day ,a few minutes research won't harm you.
I am not here to spoon feed.I find helping people a thankless task and they are mostly obnoxious,ignorant ingrates.
i have come to advise you all about this innovative method of making it,that is all..feel free to spread this around...
i tested the output of solar garden lights and they give out an output voltage from 7 v to 13 volts depending on model and this is usually pulsed rapidly.
( i used a diode capacitor smoothing filter to measure the voltage.
(optional:- you can either smooth it using a diode/capacitor or just leave it as is.)
simply remove the led and attach your 2 silver wires which should be spaced by 1 inch to 2 inches apart to the leads to which the led was attached.
insert parallel silver wires into a glass beaker filled with boiled water.That is it.Very simple.
colloidal silver will be produced very slowly and of very high quality by a solar garden light at night automatically as solar garden lights switch off during the day to charge the battery.Off course you can start it manually by covering up the light sensor or solar cell to simulate darkness.
the whole thing can be build out of the garden solar light including attaching the silver wires to THE HOUSING!
only costs $2 for solar garden light plus silver rods which cost $20 i think...
it can be left next to the window...MAKE SURE WATER FILLED BEAKER IS SHIELDED FROM THE SUN to avoid degrading colloidal silver.use silver paper or cardboard,etc.
the pulsed very low current of less then 0.0003 amps and 7 to 13 voltage spikes will produce very small particles of silver.
some solar lights produce about 7 or 8 volts and some 13 volts.
but in any case this IS very cheap and very simple and very effective way of doing it.
also instead of removing the led altogether just cut ONE of the led's leads and use the output from their to connect to the silver wire rods.
in effect the led will be in series with one of the rods and will give a visual indication of current flowing through the water.The led could be even angled downwards towards the water into which the electrodes are immersed and be even bright enough to show you the colloidal silver as it turns cloudy very slowly.
optional:- replace WHITE LED with RED LED as RED LED absorbs only 1.5 volt instead of 4 volts.
It will take a long time to make the colloidal silver but this is not for MTV attention span people.Set it and forget it on the window sill.
optional refinement:- A piezo sounder with a inert plastic rod glued to it and dipped in the water connected to both silver rods in parallel and immersed in the water can act as a ultrasonic sonic stirrer.. .but it will take even longer to make the colloidal silver which will be of very high quality.
Remember lower currents produce higher quality and smaller sized colloidal silver particles.
any comments?
velly velly cheep. no i am not chinese either,that was a joke.You will be grateful to know.
lol
